The options available in the “Graphical settings” tab depend on the selected graphic. For example, list and table graphics have different options to individual graphics. The focus of this topic is on the basic handling of graphical settings. To enhance comprehension of specific options and functionalities, such as style modification, filtering, and special configuration for individual graphics, these are explained separately.

|
Graphical settings
This document provides a rough overview of the available graphical settings options and how to handle them.
|
English:PDF | German:PDF |
Table of Contents
1 Foreword
This manual describes the possibilities of the basic graphics settings.
Exceptions are the special graphic settings for the individual graphics, which are explained separately in the manual for the respective graphic.
All the possibilities here, which are covered by the styles, are no longer explained in detail. Background colours, font sizes, line colours and the like. Since the introduction of the styles in which this can be set globally, it is no longer recommended to do this specifically for a graphic.
Furthermore, the "same" options are sometimes structured differently in various graphics. Here we try to explain them more globally.
More or less options are available in the different modules. Since most of the options are available in the process analysis module, the explanation will be done on this module.
Options that are only required for a specific graphic are explained in the manual for the respective graphic.
2 Display 1
2.1 Font
The fonts are to be predefined globally via the styles.
2.2 Lines / Symbols
The fonts are to be predefined globally via the styles.
2.3 Info
The appearance of the individual info elements can be set globally via the styles. The individual elements can be activated separately for the graphics. Depending on the graphic, more or fewer elements are available.
|
|
Especially with the value curve, "Info centre" should no longer be used. This position is used for the legend in the increasingly used multiple displays, e.g. overlaid gradients. A double configuration is not possible. |
|
|
The display here shows both options at the same time, "Info on top" and "Headline on part type change". However, it does not make sense to activate both of them. Depending on the option "Part type reference", an overview graphic is either displayed per part, in which case the option "Info on top" makes sense, or across parts, in which case the option "Heading on part type change" makes sense. |
2.3.1 Configuring the info content
As far as the content of "Info on top" is concerned, it is recommended to configure this globally via the style.
The content of "Heading on part type change (group change)" can be configured directly in the graphic, but the procedure is the same for all elements.
Next to the option to activate is the "Edit" button
With a right mouse click on existing fields, they can be edited, other contents can be selected:
With the option "new field" further fields can be added
From the "Output Point - List" the new fields can be moved to the desired positions:
2.4 Graphic Style / Info - Style
Only if no style has been defined as the standard should an individual style be selected here for a graphic!
This option was created as a "playground" for clients to see how styles affect graphics.
One recommendation is therefore to carry out this "playing" with a user newly created for this purpose.
3 Axes and limits
3.1 Value axis
The options of the value axis concern the Y-axis for progressions, the X-axis for graphics such as histogram or probability network. Depending on the graph, more or fewer options are available here.
3.1.1 Value scale
The first block is the representation of the value range, shown here as an example once as absolute + relative with a defined description.
3.1.2 Values out of tolerance
In the value curve, the measured values outside the specification limit can be labelled:
The use of this option is only recommended if there are few values in a representation and few measured values outside the specification limit.
3.1.3 Configuration of the hints in graphics
This option only has an effect if the information on individual values is active in qs-STAT or solara.MP (this function cannot be used in the O-QUIS products).
3.1.4 Fix distances
|
|
Pure project option. It is not recommended to use these options in normal operation! |
This limits the distances to the left and right of the actual course of values. Any content that is then no longer visible is simply cut off.
3.1.5 Display catalogue entirely
This option only has an influence for ordinal characteristics.
An ordinal characteristic is considered, which has a 5-level sub-catalogue in the background. However, only 3 values from the 5-level catalogue are present in the values.
If the option "Display catalogue entirely" is now set, the entries of the sub-catalogue which are not present in the current characteristic are also displayed as a value for the Y-axis:
3.2 Additional data axis
The 3 main configurations of the additional data axis are also preconfigured as such in the standard reports. Display only with current value number, display with selected additional data or as a true time axis.
3.2.1 Time axis
In the display of the time axis, the gaps between the measurement times can only be clearly seen in the value progression. In this case, the time span is recorded from the oldest to the newest measured value, and the measured values are displayed at the time.
In the configuration of the time axes, different colours can be given to the different time indications. Basically, however, only the required times are shown in the axis.
|
|
If this display is selected, various other options are deactivated, e.g. the separating line for additional data changes or the display as a bar instead of a value point. It is therefore advisable to leave this display to the reports and not to save it as the default. |
3.2.2 Event display
Here you can select whether events are only displayed as symbols on the axis:
Or whether additional lines are drawn to show the short text of the catalogue:
3.3 Quantile limits
The option of quantile limits is explained on the histogram. The 99.73% quantile limits are shown in the standard.
If desired, this can be changed and the intermediate values can also be displayed. Only the largest values given are labelled:
3.4 Characteristic values / limit values
Depending on the selected graph, more or less "Limits / Characteristic values" can be activated here.
The graphic configuration of the lines, which could be carried out to the right of each line, should be defined exclusively in the styles. This is described in the manual of styles, so it will not be discussed here.
The explanation of the meaning of each of the lines is also omitted here. The meaning of limits , given by e.g. the feature mask, or the knowledge of the calculated characteristic values such as mean value, estimator is assumed here.
3.5 Display limit
By default, each graph always tries to display all specified limits, lines and measuring points. In the case of outliers, for example, this can lead to a compression of the graph:
One of the most common methods is to now set this to a % range of tolerance:
Or, in the case of quality control charts, to the % range of the quantile limits:
Other special options of the display limitation are explained with the respective graphics.
3.6 Estimator
The estimators are to be configured similar to the quantile limits and are only visible in the quality control charts. This allows the estimators used for the QRK calculation to be displayed.
A common misconception is that the quantile limits are equal to the estimators or even to the action limits. For this reason, they can be presented separately here.
4 Display 2
The second area of the display contains further global settings. Depending on the graphic, these are available in different numbers and have different effects. As in the previous chapters, only standards are explained here; special options that only apply to certain graphics are described in the respective graphics.
4.1 Transformed values
The basic setting here is to display the values in graphs that the end customer can work with. However, in the case of special distribution forms, such as logarithmic normal distribution, a "transformation" of the measured values and specification limits is carried out before calculating the characteristics in order to bring the values into a calculable range. This can be an offset, a logarithm or similar. Here, using the example of a histogram with the logarithmic normal distribution, once as a "normal" representation, once in the transformed range.
|
|
|
|
|
|
4.2 Axes on/off
With the option, the axes of graphics can be shown and hidden.
|
|
|
|
|
|
A special case is the option "Keep axes always shown". The reason for this option is as follows:
If the size of the axes in graphics makes the actual graphic so small that they are hardly visible, the axes are automatically hidden.
As an example, a value curve with additional data display:
If this is pushed a little smaller, the axes are automatically hidden:
If the option is set to force the display of the axes, they will still be displayed to a certain extent.
|
|
If the graphic is displayed even smaller so that the axes take up the entire drawing area, this option is also ignored and the axes are hidden! The use of this option must therefore be considered with regard to the elements to be displayed. |
4.3 Language selection
As a volatile setting, the language of a graphic can be changed temporarily (provided the language licences have been purchased). Here as an example a form, the software runs in English, the form was changed to Portuguese.
4.4 Rotate graphic
This option is possible for graphics such as the histogram, but also for overview graphics such as box plots and C-values.
|
|
|
|
|
|
4.5 Change display / 3D settings
In some graphics a 3D representation is possible, or is even automatically selected via other graphics options. This can be activated with the 3 options.
|
Histrogram |
|
|
2D position |
|
|
3D position |
|
With the additional option of the 3D display, the angles can still be specified:
4.6 Background
These settings are intended for the user's personal settings deviating from the standard style.
4.7 Lines + Symbols
These settings are intended for the user's personal settings deviating from the standard style.
4.8 Allocation
This option only has meaning in procella within the overview - input and is explained with the corresponding graphics.
4.9 Grid lines
Net lines can be displayed in various graphics:
|
|
|
|
|
|
|
|
4.10 Colour
In almost all graphics, it is possible to switch to black/white or white/black in addition to the colour display:
|
|
|
|
|
|
|
|
4.11 Configure application bar
An example of a application bar is configured in Characteristics 9. This can be used to call up functions or other graphics from a graphic, from individual characteristics graphics or from overview graphics. Users of procella know the control bar in detail.
After pressing the button, the configuration of the application bar opens.
A detailed description is given in the procella documentation. Therefore only rudimentary explanations are given here
The upper part specifies where the bar is to be placed and how many buttons are to be available:
Desired graphics must first be inserted into the selection list:
These can then be dragged onto the buttons. Any functions / graphics already there are exchanged.
4.12 Application bar
Only visible if a application bar has been configured. This can then be activated / deactivated with the two options
4.13 Configure window title
The option of window title configuration should only be carried out when various overview graphics, e.g. characteristics, have been configured and their use has been determined.
These would be, for example:
In solara.MP the definition of titles of "Characteristics", if they are aligned to a certain evaluation type.
In qs-STAT, the definition of titles of "Characteristic values Characteristics", if these are aligned to certain characteristic types such as attributive or positional tolerances.
The window title assignment also follows the configuration management. Therefore, this should only be set by experienced key users.
Pressing the button opens the dialogue. Only those languages are displayed whose licence is available.
Now the title can be changed in all languages:
|
|
Your own window title is saved immediately when you press the "OK" button! |
In most cases, the changed text is taken over directly for the entry in the ribbon as well as for the title of the graphic:
4.14 Legend
Is described in the multiple display manual where this only applies.
5 Save
Almost all changes made to the graphics must be saved, otherwise they will be discarded again when the graphic is closed.
A special feature occurs when saving changes that may be predefined by a set style. As soon as a style is active and an element that is predefined in the style is changed (e.g. background colours, fonts, line widths), the system asks whether an overlay should be saved for this graphic.
If this is saved, the graphic no longer uses the style. Here is an example: The value curve was saved with an overlay.
To undo this, the user must have the saved graphic deleted by an administrator in the user administration.
However, the overlay is saved for a defined style. If a different style is saved as the standard and no overlay has been saved for this graphic, the graphic first falls back on the new style.
6 Reset
The option "Reset to default" is intended exclusively for the case that a graphic has been configured and not yet saved. In this case, the standard saved by the user can be restored with this button.
The option is NOT used to delete user-specific configurations.
As ConfigurationUser, there is also the sub-option "Set to factory defaults". In this case, all configurations in the configuration database are deleted and the standard of the application (i.e. what the *.exe "knows" in the background) is used. This should only be done after consultation in the project.


